Electromagnetic sieve shaker 918 control is used in research & development, quality control of raw materials, interim and finished products as well as in production monitoring. The controllable electromagnetic drive offers an optimal adaption for every product. Sharp fractions are obtained even after short sieving times.

These Sieve Shakers are activated by electromagnetic impulses, they are recommended to perform sieving tests where high precision and performance are important, and where continual and intense uses are required.

It is particularly designed for test sieves with a diameter of 200 mm x 50mm h. They are therefore suggested for accurate sieving tests, also on fine materials. These Electromagnetic Shakers are of simple and sturdy construction, can hold up to 8 sieves .

Operation mode	Intermittent and Continuous Shifting Motion
Intermittent operation	At Intervals (0.5 sec)
Capacity	Up to 8 Sieves (Test Sieve Dia form 200mm x 50mm h)
Shake time	Programmable Shake Time from 1min to 99min
Display	20 x 4 Alphanumeric LCD with Backlit Display
Keypad	Fully Alphanumeric Keypad
Power level	Programmable (from 1 to 20)
Noise	Very Low Noise Operation
Security	2 Tier Password Protection Facility (Admin & User)
Printer	RS 232 Port for Serial Printer using 80 Column Dot Matrix or Thermal Printer
Dry sieving	Standard (Wet Sieve Optional)
Power	220V AC, 50 Hz
Dimension (L X B X H)	310mm x 390mm x260mm (approx.)
Weight	49 kgs approx. (without Sieves)

Note : Specifications are subject to change due to continuous improvements.

Microcontroller Visual Melting Point Apparatus Model 3935 with Graphical LCD display and colored TFT screen and high resolution camera. It is designed for accurate measurement of melting points and for checking the melting range of the solid samples. The apparatus consists of a silicon oil bath of about 200 ml capacity, covered with a Teflon cover with 5 holes, fitted with a special type of oil immersion heater and having three holes for holding the capillaries, one for boiling point tube and one for the thermometer.

The plateau temperature and the heating ramp rates are fully programmable using ‘Plateau’/ ‘Ramp’. The plateau temperature allows the user to set a temperature to few degrees below the expected melting point temperature. Auto melting point apparatus will then heat to the programmed plateau temperature very rapidly. Once plateau temperature is reached the instrument will heat slowly from the plateau temperature until the powder melts on programmed ramp rate.

A high resolution camera detects the sample status. This makes it a user friendly instrument.

Temperature Range	Ambient temperature to 300 ºC
Temperature Sensor	PT 100
Temperature Resolution	0.1 ºC
Capillary Glass Tubes	75 mm
Ramp Rate	Programmable at scale of 1 – 10
Amount of Sample	Fine powder properly dried at a temperature considerably below its melting point, 4 to 6 mm high
Plateau Temperature	Programmable
Key Board	20 keys – soft touch membrane type
Heater	Immersion type
Storage	Setup Data : 100 Setups , 99 different test setups programmable by user Results : up to 300 last results
Display	240 x 128 pixels Resolution 7″ Graphical LCD Display
Clock	In-built clock with date & time display
Stirrer	In-built magnetic stirrer with adjustable speed
Printer/PC Interface	Through RS232 for serial printing using 40/80 column dot matrix printer
Power	230 V ± 10 % AC, 50 Hz
Dimensions	375 x 300 x 330 mm (L X B X H) Aprrox.
Weight	12 Kg. (Approx.)
Accessories	Box of Capillaries (set of 100), Glass Tubes for Liquid Sample (6×75 mm),Magnetic Capsule, Bottle of silicon oil (250 ml), Glass Cylindrical Beaker and Teflon Cover for beaker fitted with immersion heater, Coloured TFT Monitor, High resolution camera (In built), Instruction Manual

Note : Specifications are subject to change due to continuous improvements.

Microprocessor KF Moisture Titrator – 2760 is the finest volumetric titrator available. It uses the latest microcontroller technology and advanced engineering techniques so as to give enhanced accuracy and reproducibility. The system has user friendly prompts which guide you throughout the titration process. This titrator eliminates the use of conventional delicate and fragile glass burettes and plunger systems. It uses a highly sensitive motorized dispensing system for precise control of titrant volumes. This titrator analyses the moisture concentration of liquid samples, powder, fine particles and fiber samples that are soluble in alcohol or solvents. The moisture content is displayed in ppm, %age and mg H O.

The system has 20 soft touch membrane type keys for ease of operation. Complete alphanumeric keypad is provided so as to feed the values of sample, density, titer factor, date, time etc. The End Point indication is given by both visual LED and audible alarm. The titrator has the facility for automatically calculating the titer factor of the Karl Fischer reagent. It uses the repeated averaging method so as to give the most accurate titer value. It can store 90 user defined setup files for ease of operation and final results of 300 titration . The internal battery backup provision has been made to store the results and the other titration parameters even if the instrument is switched OFF. Provision for external printer/PC attachment is available so that any of the stored results or the calibration and validation reports as per pharma compliance can be printed even at a later stage.

Measuring Range	100 ppm to 100% of moisture
Measuring Method	Karl Fischer Volumetric Titration method.
K.F. Dispensing	Highly sensitive motorized dynamic dispensing system
Resolution of Titrant Volume	0.01 ml
Indication of Titrant Volume	0.00 to 99.99 ml on display
Moisture content calculation (Automatic)	%age : (0.00 to 100%) ppm :: (100 to 999999) mg H2O : (0.00 to 999.99)
KF Titer Factor	In-built Automatic KF Titer Factor calculation facility
End Point Alarm	Visual LED and Audible Alarm
Wait Time for End Point Alarm	Adjustable (1 to 99 seconds)
Dispensing Pump Calibration	Available through Key board
Key Board	20 keys soft touch membrane type
Sample Storage	Upto 300 samples
Display	40 x 4 Line Alphanumerics LCD Display
Clock	In-built clock with date & time display
Stirrer	In-built Magnetic stirrer with adjustable speed
Reagent Bottle	3x250ml bottle for KF Reagent, Methanol & Calcium Chloride
Printer /PC Interface	Through RS232 for serial printing using 80 column Dot Matrix Printer
Power Supply	230V A.C ± 10% 50 Hz.
Dimensions	L 362 x B 295 x H 180 mm (Approx.)
Accessories	* Dual Platinum Electrode * Titration Vessel * Built-in Magnetic Stirrer * Teflon Coated Magnetic Stirring Capsule * 250ml Bottle for Methanol * 250ml Reservoir Bottle for KF Solution *25ul Syringe * 250 ml Bottle for Calcium Chloride * Adaptor for KF Reservoir *Adaptor for Acetone Reservoir Bottle * Set of Dispenser Tubes * Set of Connecting Tubes * Main Lead *Instruction Manual

Note : Specifications are subject to change due to continuous improvements.

EI Digital Antibiotic Zone Reader provides the user, distance in mm with accurate and fast method for determining the strength of antibiotic material. It functions by measuring the diameter from 0 to 80.0 mm of an inhibition zone in a petri-dish.

Wells are created on a petri-dish, prepared with agar – agar solution and inoculated with bacteria. After incubation, the bacterial growth cover the dish except for a circular inhibited zone around each disc, it being a function of the strength of the antibiotic.

The zone reader accurately measures the diameter of the inhibited zone to 0.1 mm within range of 0 to 80.0 mm diameter. Light is passed through the transparent and semitransparent portions of the agar from a source at base towards up. It then passed to a reflecting mirror supported by an arm above the unit, which reflects the light to glass prism mounted at the front of the unit and magnified image of the zone of inhibition is clearly visible on the prism.

Zone Diameter Range	0 to 80.0 mm
Accuracy	0.1 mm
Resolution	0.1 mm
Illumination Lamp/LED	12 V DC
Display	4 digit seven segment LED display
Power Supply	230V±10% AC, 50Hz
Dimensions	12’’ X 14’’ X 17’’ (L X W X H)
Weight	Net 10 Kgs. (Approx.)

Note : Specifications are subject to change due to continuous improvements.

Melting Point Apparatus with TFT display & 4 digit LED display is designed for accurate measurement of melting points and for checking the melting range of the solid samples. The apparatus consists of a silicon oil-bath of about 200 ml capacity, covered with a teflon cover with 5 holes, fitted with a special type of oil immersion heater and having three holes for holding the capillaries, one for boiling point tube and one for the thermometer. It is supplied with high resolution camera & TFT display screen to view sample in capillaries.

The apparatus consists of an in-built magnetic stirrer, an electronic controller with indicator for precisely adjusting the rate of heating of silicon oil-bath, an ON/OFF switch, a pilot lamp, a magnifier, glare free background illuminator and a High/Low range temperature selector switch and digital temperature indicator with PT-100 RTD sensor.

The ‘Start’ switch is used to start the measurement of melting point. User can stop the process of measurement using ‘Stop’ switch after the instrument reaches the melting point of the sample. The display will always show the last temperature where ‘Stop’ switch was pressed in last measurement. Clear switch is used to clear the display to zero.

TFT Screen	Available with high resolution camera for viewing capillaries
Display	4 Digit, 7-Segment LED Display
Temperature	0 – 300 °C
Resolution	0.1 °C
Capillary Glass Tubes	75mm long, 0.8 to 1.1mm internal diameter
Boiling Point Glass Tubes	6×75 mm glass tube
Sample Amount	Fine powder properly dried at a temperature considerably below its melting point 4 – 6 mm high
Oil-Bath	Silicon oil-bath beaker 200 ml capacity with Teflon cover fitted with oil immersion heater. It has three holes for holding the capillaries, boiling point tube and thermometer
Stirrer Speed	Controllable with front knob
Power	230 V ± 10%, 50 Hz. AC
Dimensions	370 x 290 x 290 mm (L x B x H) (Approx.)
Weight	12 Kg (Approx.)
Accessories	Box of Capillaries,  Glass Tubes for Liquid Sample (6x75mm) -2 Nos.,  Magnetic Capsule, Bottle of Silicon Oil – 250ml, Glass Cylindrical Beaker with Teflon cover for beaker fitted with immersion heater, Operation Manual, Dust Cover

Note : Specifications are subject to change due to continuous improvements.

Disintegration Tester is a solid state instrument designed for the accurate estimation of disintegration time of tablets as per IP/USP standards. The instrument is designed to test two batches of six tablets, simultaneously. The unit is extremely useful for pharmaceutical industries. It is used in quality control and R & D to determine compliance with the disintegration requirement of the tablet and capsule as per USP/BP/IP standards.

Instrument uses the latest microprocessor technology and advanced engineering techniques so as to give enhanced accuracy and reproducibility. The system has user friendly prompts, which guide you throughout the measurement process.

The instrument has two basket assemblies with independent timers and motors. The timers and temperature are displayed on 5 digit and 3 digit seven segment red LED displays respectively. Each timer can be set and used individually. The baskets are automatically positioned at the top when the test is over.

The unit is provided with two glass beakers having capacity of 1000 ml with arrangement to hold temperature sensor placed in the sturdy, acrylic water bath. The large spread out stainless steel heater ensures perfectly uniform heating. The instrument has a dual channel temperature system with sensors to monitor the test temperature of disintegration beaker as well as water bath. The temperature of the water bath and vessels are accurately maintained using highly accurate sensors and microcontroller technology. The basket speed is accurately controlled and maintained as per IP, USP specifications.

Number of Baskets	2
Stroke Length	55 mm ± 2 strokes / minute
No. of Timers	2 Timers
Timer Display	5 Digit LED Display for each Timer
Timer Range	1Sec. To 9 Hrs. 59 Min 59 Sec.
Keyboard	Soft touch membrane keys
No. of Motors	2
Temperature Display	3 Digit LED Display
Temperature Range	20.0°C to 39.9°C
Temp. Control	Microprocessor based using PT100/ semiconductor sensor as per IP/USP
Accuracy	+ 0.2 °C
Reaction Vessel	1000 ml
Heater	0.5 KW
Electrical Supply	220/230 V AC ±  10%, 50/60 Hz, 44VA
DIMENSIONS (W x H x D)	36 cm x 20 cm x 32 cm
Accessories	Reaction Vessel – capacity 1000 ml – 2 Nos. Two USP Baskets with 6 Tubes and 6 guided Discs, each External Temperature Sensor Mains Lead Instruction Manual Dust Cover

Note : Specifications are subject to change due to continuous improvements.

GENERAL
Stations	14 stations in Model – 2914
	12 stations in Model – 2912
Display	20 x 4 line alphanumeric LCD display with backlit
Keyboard	19 soft touch membrane type keys
LED’s	4 LED’s for different status indications. 3 LED’s for test status like Run, Alarm, End & 1 LED for heater ON/OFF status
Setup Data	20 different test setups available in routine and sustain modes
Printer Attachment	Provision for the attachment of dot-matrix printer with centronics parallel port interface available
STIRRER
Speed	25 to 200 RPM ±1 RPM
Resolution	1 RPM
Accuracy	± 1 RPM
TEMPERATURE
Range	30 to 50o C
Accuracy	± 0.2o C
Temp. Control	Microprocessor based using PT100/ Semiconductor sensor as per IP/USP
SAMPLE
Reaction Vessel	1000 ml jar with stirrer pedal and basket
Power Supply	230 V ± 10%, 50 Hz. AC
Heater	1900 W

Note : Specifications are subject to change due to continuous improvements.

Display	LCD with backlit display
Keyboard	User Friendly 9 Keys operations
Hardness Range	5-500N
Hardness Accuracy	±0.05% FS
Measuring Units	N(Newton), KGF (Kilogram Force) and Lbf (Low bound Force)
Interface Ports	RS-232
Dimensions	360 x 65 x 100 mm
Electrical Power Adapter	230 V, 50Hz to DC 12V, 300 mA
Battery	1200 mAH, 8.4V, Ni-Hi Rechargeable Battery
Peak Force Measurement	Yes
Acrylic Safety Glass Cover	Yes
Stored Results	Upto 10 (also calculate the average value of test results)
Zero point adjustment for Calibration	Yes
Auto Unit Conversion	Yes
Programmable T1, T2 tolerance	Yes
Tablet Size	Yes (2mm to 28 mm)

Note : Specifications are subject to change due to continuous improvements.